欢迎访问过程工程学报, 今天是

过程工程学报 ›› 2021, Vol. 21 ›› Issue (8): 918-925.DOI: 10.12034/j.issn.1009-606X.220256

• 流动与传递 • 上一篇    下一篇

喷动流化床最大喷动压降的多因素影响与关联

付爽1, 王东祥1,2*, 俞建峰1,2, 金海安1
  

  1. 1. 江南大学机械工程学院,江苏 无锡 214122

    2. 江南大学江苏省食品先进制造装备技术重点实验室,江苏 无锡 214122

  • 收稿日期:2020-08-07 修回日期:2020-09-12 出版日期:2021-08-28 发布日期:2021-08-24
  • 通讯作者: 王东祥 dxwang@jiangnan.edu.cn
  • 基金资助:
    国家自然科学基金青年项目;中国博士后科学基金

Multi-factor effects on and correlation of maximum spouting pressure drop in spout-fluid bed

Shuang FU1,  Dongxiang WANG1,2*,  Jianfeng YU1,2,  Hai'an JIN1   

  1. 1. School of Mechanical Engineering, Jiangnan University, Wuxi, Jiangsu 214122, China

    2. Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment & Technology, Jiangnan University, Wuxi, Jiangsu 214122, China

  • Received:2020-08-07 Revised:2020-09-12 Online:2021-08-28 Published:2021-08-24
  • Supported by:
    National Natural Science Foundation of China;Postdoctoral Science Foundation of China

摘要: 基于截面200 mm×20 mm,高1600 mm,锥角60°的矩形喷动流化床,以二组分混合颗粒、单一组分球形颗粒及非球形颗粒为物料进行最大喷动压降的实验研究。结果表明,最大喷动压降随静止床高、颗粒密度、颗粒球形度及二组分混合颗粒体系中沉积组分分率增加而增大,随流化气速增大而减小;增大颗粒粒径或喷口宽度,呈现先减小后增大趋势,存在极小值;对于非球形颗粒及混合颗粒,其床层总压降随表观喷动气速变化的规律与单一组分球形颗粒相同,但相同条件下的前者压降波动幅度大于后者。以实验测量的854组数据为基础,结合量纲分析法建立了最大喷动压降预测关联式,与测量值及文献实验数据吻合较好。

关键词: 喷动流化床, 最大喷动压降, 二组分混合颗粒, 非球形颗粒, 预测关联式

Abstract: The maximum spouting pressure drop (Δpm) is one of the important parameters for the design and operation of the spout-fluid bed. Almost all the literature correlations for predicting the Δpm were developed from single-component particles or spherical particles, and hence were with some limitation in actual application. In view of this, with binary particle mixtures, single-component spherical particles and non-spherical particles as experimental materials, the Δpm was studied based on a rectangular spout-fluid bed with cross section of 200 mm×20 mm, height of 1600 mm and conical base angle of 60°. The results showed that the Δpm increased with the static bed height, particle density, particle sphericity and deposition component ratio, and decreased with the fluidized gas velocity. While with the increase in particle size or spout nozzle size, it went down firstly and then up with a minimum pressure drop. For non-spherical particles and binary particle mixtures, the variation of total pressure drop with superficial spouting gas velocities was found to be similar with that of single-component spherical particles, while the fluctuation range of total pressure drop was larger under the same conditions. Based on the 854 sets of measured data by experiments, a predicting correlation of the Δpm was proposed by dimensional analysis method, which was in good agreement with the measured data in this work and the experimental data in literature.

Key words: spout-fluid bed, maximum spouting pressure drop, binary particle mixtures, non-spherical particle, prediction correlation