欢迎访问过程工程学报, 今天是

过程工程学报 ›› 2017, Vol. 17 ›› Issue (5): 1035-1040.DOI: 10.12034/j.issn.1009-606X.217147

• 过程与工艺 • 上一篇    下一篇

多功能铁水包周转数计算模型

谷宗喜1,徐安军1*, 贺东风1,吴 伟2, 刘晶波2,韩伟刚3     

  1. 1. 北京科技大学冶金与生态工程学院,北京 100083;2. 重庆钢铁集团股份有限公司,重庆 401258; 3. 钢铁研究总院先进钢铁流程及材料国家重点实验室,北京 100081
  • 收稿日期:2017-02-22 修回日期:2017-03-28 出版日期:2017-10-20 发布日期:2017-10-10
  • 通讯作者: 徐安军 anjunxu@126.com
  • 基金资助:
    国家重点研发计划课题:钢铁生产流程工序匹配与系统节能;自然科学基金项目:面向工序装置尺度的钢铁制造流程一体化智能调度建模与仿真

Calculation Model for Turnover Number of Multi-functional Hot Metal Ladle

Zongxi GU1,  Anjun XU1*,  Dongfeng HE1,  Wei WU2,  Jingbo LIU2,  Weigang HAN3     

  1. 1. School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China; 2. Chongqing Iron and Steel Co., Ltd., Chongqing 401258, China; 3. State Key Laboratory of Advanced Steel Processing and Products, Central Iron and Steel Research Institute, Beijing 100081, China
  • Received:2017-02-22 Revised:2017-03-28 Online:2017-10-20 Published:2017-10-10

摘要: 在综合考虑铁水包备包生产及高炉配罐制度等因素的基础上,建立了多功能铁水包周转数计算模型,即铁水包周转数由工艺要求数、备包数及高炉配罐富裕数组成. 依据模型计算出重钢新区两座高炉?两座转炉模式下铁水包周转数为16个. 结果表明,减少铁水包周转数的关键在于减少重包和空包的“缓冲容量”,为此需优化高炉配罐制度及连浇炉数. 单一优化配罐制度及连浇炉数均可减少2个铁水包,联合优化配罐制度和连浇炉数可减少4个铁水包.

关键词: 铁水包, 周转数量, 计算模型, 缓冲容量, 甘特图

Abstract: Calculation model for turnover number of multifunctional hot metal ladle was proposed based on comprehensive consideration of ladle preparation and ladle allocation method for blast furnace. Ladle number was composed of three parts which were loaded ladle number for processing needs, required preparation and unloaded ladle number for excessive allocated for blast furnace. Ladle turnover number in 2 blast furnace?2 basic oxygen furnace production mode in Chongqing steel plant was obtained as 16 by applying the model. The results showed that decreasing the buffer capacity of loaded and unloaded ladle should be a crucial step to reduce the ladle turnover number. Therefore optimizing ladle allocation method and continuous casting heats were supposed to be adopted as feasible measures. Individual optimization of ladle allocation method and casting heats can both contribute to the decrease of 2 in ladle number. In addition, ladle number can be reduced by 4 with joint optimization according to the model.

Key words: hot metal ladle, turnover number, calculation model, buffer capacity, Gantt chart.